ATTENTION: Full Version only for Rei2 with serial number beginning RE*. Do not download the software on Rei2 without *. ***************BUG FIX******************* Version 1.0 1) String "Pod n°" not displayed in "line status" mode 2) An error occurred when net times were printed with a time event assigned to another bib number 3) If REI2 was switched off in the "line status" mode, REI2 could no longer check the status of the Pods correctly 4) An error occurred when REI2 was switched off before entering a race: this made REI2 crash 5) Display of running time on the uGRAPH displayboard with medium proportional characters fixed 6) Total-split time display added also in single start sequences (previously there was only total time) 7) If a logical channel is not assigned to a physical channel, when an event is acquired on the physical channel it is lost Version 1.01 1) The micrograph displayboard with the 4th, 5th and 6th positions in the ranking displayed did not give the time of the 6th competitor when this competitor finished Version 1.03 1) An error in the display of "number and time" by the single microtab displayboard fixed Version 1.04 1) A problem in race cancellation was fixed 2) Display on displayboard of previous/next time fixed 3) Check added on number of displayboards possible depending on the serial speed Version 1.05 1) Error in printing of race by points configuration fixed 2) Error in group ranking for single/group starts fixed 3) Error in transferral of names with more than 24 characters fixed 4) Error in disqualification of a competitor at the start in Show Jumping fixed Version 1.05.1 1) Error in wireless event reception fixed 2) Rounding off of times changed to 6 in Swimming program Version 1.7 1) Protocol for download of automatic start data from PC changed: "DATE" Version 1.7.4 1) Error in sending events from PC fixed Version 1.7.5 1) Bug in the generation of programming file mg_fw_rei2_v1_7_4_*.exe detected and fixed Version 1.7.6 1) Error in elimination of a competitor during countdown in Show Jumping program fixed Version 1.7.9 1) Functioning of leds re-enabled 2) Error in calculation of speeds fixed Version 1.8.2 1) Recall old race fixed Version 1.8.8 1) Error in download of automatic start data from PC changed fixed ***************NEW FEATURES********************** Version 1.01 1) In the displayboards with proportional strings, the whole maximum available length for display is used 2) Possibility of setting the confirmation time for the stop in single/group starts introduced so as to immediately send the event on the serial (the choice can be made in the submenu 3/1/1/1c of "Software configuration") 3) Possibility of alternating display of split and lap times on the displayboard in single starts introduced (the choice can be made in the 3/2b sub-menu of "Displayboard configuration") 4) Parallel displayboard added: 2 uGRAPHs, position, number (blue track and red track)and running time Version 1.02 1) Possibility of displaying the time on the displayboard without punctuation. Version 1.03 1) Possibility of inserting a different displayboard viewing pause for the lap. 2) A single Micrograph displayboard: running time with large characters 3) Micrograph and Microtab displayboards with scrolling rankings 4) Displayboard 2 Micrographs: three lines with running time and the competitor placed before and after in the ranking 5) Displayboard 4 Microtabs: time of competitor placed before/after in the ranking 6) Displayboard 2 Micrographs: position, number, name, gap and time 7) Battery management 8) Parallel program: management of maximum gap 9) Management of Gundersen pursuit races 10) Rankings available also for laps with the same number of laps Version 1.04 1) Display and printing of "forerunner" name in the forerunner mode 2) Beeper program* 2) Multilane group start configuration added 3) Alge displayboard: Best time* 4) Alge displayboard: Gap* 5) Synchronization test 6) Digitech displayboard: running time 7) Rankings based on bib number 8) Microtab displayboard: dynamic LAP time 11) New programs: Show Jumping and Swimming * Version 1.05 1) Possibility of inserting 0 as penalty for exceeding maximum time in Show Jumping 2) Possibility of displaying name of horse and its rider in Show Jumping 3) Possibility of choosing from 1 to 5 best runs for calculation of total time in single/group starts 4) Ranking added with run times of all the athletes and all the runs 5) Possibility of inserting DQ, NF and DNS in start lists 6) Possibility of disabling the checking of length of data transmission to the displayboard 7) Displayboard: 2 Seikos only for Show Jumping program* 8) Displayboard: 2 Alges only for Show jumping program* Version 1.05.1 1) Possibility of displaying competition already finished in Show Jumping Version 1.6 1) Download of start lists for swimming. See protocols 2) Possibility of inserting times with computer 3) Possibility of generating an impulse on pin 6 of the digital output at time decided by user Version 1.7 1) Calculation of rankings for different groups accelerated 2) Printing of time events in Basic Stopwatch 3) In the tick output for parallel the track is displayed instead of the number of days 4) Confirmation time in PC-Online can be set by user 5) Possibility of commanding display of a competitor on the displayboard via computer 6) Dynamic definition of groups 7) Filter on logical channel in "Time events" 8) Possibility of sending printed data on serial 9) Possibility of acquiring and printing climatic data from the sensor 10) Extraction of winners in "Start order calculation" of Parallel Slalom program 11) In Show Jumping "Disqualification" has been changed to "Elimination". Those eliminated are considered to be still in the ranking 12) New possibilities for displayboard viewing added Version 1.7.4 1) Gap display added on single uTab displayboard 2) Possibility of modifying distances in Swimming program in manual configuration 3) Non-starters, Non-finishers and Disqualified are sorted by bib number when printout is made 4) Display on row 15 of double uTab of bib number and name of next to start added (only in Single Starts if beeper is on) 5) Climatic data output added in offline transmission("Net times...Yes" must be configured) 6) Possibility of sending time events as net times in PC-Online program 7) Possibility of adding on times of previous runs in Show Jumping program 8) Possibility of changing logical channel for skipped events in Single-Group Starts program 9) Static request to send only modified events added (Type of information: 'l'. In this case the bib number is the number of modified events to be sent (0=all)) 10) Possibility of sending a string for printing '0x19 string 0x0D 0x0A' (Example:0x19Test0x0D0x0A) 11) Display on single uTab on row 0 and on single uGraph on row 1 with time of day in PC-Online program 12) Show Jumping program modified: possibility of setting 1 point every x seconds independently for phase 1 and phase 2 13) Displayboard: 2 uGraphs, running time and last 2 finished 14) Displayboard: 1 uTab, running time and, at the finish, number and position 15) Possibility of modifying race number in Swimming program 16) Possibility of printing downloaded start lists in Swimming program 17) "Continue" added in Show Jumping program. If the competitor is eliminated in the first phase because of penalties, pressing ALT + F3 puts him/her through to the second phase. Version 1.7.6 1) "Retired" added in Swimming program (++) 2) Display of time 0.0 on displayboard added in Group Starts when selected competitor must start 3) Time of rotating ranking can be set by user 4) Invert first (0 = all) added in creation of bibo list 5) Management of number from Linkgate inserted 6) Possibility of checking existence of same event in PC-Online added 7) Possibility of in background downloading of lists without entering "Upload data from PC" menu 8) LinkPods connected indicator(only for Rei2 with a core version of 12 or higher) 9) Possibility of connecting a modem to computer A or B output (in "Modem" menu) 10) Radio Modem protocol added only on computer B. Functioning is similar to Rei2Net. Only two stopwatches can be connected. Suitable for transmission of events via modem. 11) Possibility of having competitors in the ranking who have not completed full laps in "Rankings and other printouts "->"Print and viewing mode"->"Consider previous laps in ranking") 12) Possibility of setting maximum number of athletes in the ranking in "Rankings and other printouts"->"Print and viewing mode"->"Max athletes in ranking") 13) Oldtime race configuration in PC-Online program 14) Single ALGE displayboard added for Parallel and Dual Timer programs 15) New ranking printouts added in Swimming program 16) If in single or group starts a "Last relay lap" different from 0 is chosen, different laps can be set for each group (in "Enter/Modify groups" menu by pressing ALT + F3) 17) Filter on line noise added (by default on START line). To set the other lines, the "Line configuration" menu -> "Main lines noise filter" (only for Rei2 with a core version of 11 or higher) 18) Maximum number of swimming races 200 19) In single/group starts it is possible to disactivate automatic stopping of cursor when a competitor finishes (In "Timing " -> "C.Start." press ALT + F1) 20) Manual event block for 2 seconds after start of race in Swimming program 21) TimeLink protocol added to make it possible to connect the device to computer B 22) Possibility of acquiring and printing data from the wind gauge and light sensor 23) New static requests added (see "Transmission protocol" manual) 24) MANUAL logical channel added in "Line configuration"->"Assignment of main lines and keys". The MANUAL event acquired is printed but not saved. Suitable for managing a backup manual independently of the main time-keeping (not active for the Parallel program) 25) Possibility of sending only times to which a bib number has been assigned in PC-Online 26) Rei2Net function improved 27) Radio reception of events improved 28) Possibility added also in the displayboard menu of delaying display of the tick and displayboard 29) Manual insertion of automatic start time added 30) Show Jumping program: possibility of applying time corrections to the output of the displayboard only at the end of the competition Version 1.8.1 1) Addition of word "series" in Swimming program 2) Addition of paper-save mode (in " Software Configuration" -> "Compact times print") 3) Possibility of choosing the position of the red and blue track in the Parallel program (in " Software Configuration" -> "Left track") 4) In the Swimming program the sound signalling of an event is also repeated on the loudspeaker output 5) Pause after confirmation of times eliminated in Parallel and Dual timer programs 6) Calculation of ranking by groups improved 7) Addition of rapid selection menu in Single and Group Starts. In "Timing" press ALT to access rapid selection menu 8) Addition in Single and Group Starts of new "Semiautomatic" skip mode. The first lap or stop event is managed only if there is a number which is finishing. The following events are skipped. The event is also managed outside the timing menu. Active also for the START line 9) New menu for the management of skip events in Single and Group Starts 10) Addition of possibility of setting the synchronization signal repetition time on pin 6. 11) Acquisition of events from pod improved 12) Addition of possibility of modifying the automatic start time in the program Single and Group Starts "Starting list manager"->"List Manager Automatic starts"->"Input/Modify Automatic start"-> "Input start list" -> "Modify" press ALT + F3) 13) Addition of Rei2Net to Dual timer program 14) Addition of choice of displayboard display of only finish or intermediate and finish ("Displayboard Configuration" -> "Show ranking") 15) Addition of possibility of repeating display of ranking on the displayboard in the program Single and Group Starts. Press ALT + arrow key. Keep ALT pressed down to continue rolling of ranking. 16) Addition of finish sequence in PC-Online program in bib assignment configuration (in "Timing" press F4) 17) Edit menu in PC-Online programme modified 18) In the Showjumping program it is no longer necessary to wait for the end of displayboard viewing to confirm the competitor's finish. Version 1.8.2 1) Addition of two new micrograph displayboards for new font 2) Addition of the possibility of setting precision at 1/10000 also for the Parallel and Dual Timer programs 3) Addition of new characters (e.g. ä, ö and å) 4) New display mode added on displayboard: "Running time" or "Time of day" 5) Management of thousandths of a point added to Show Jumping program 6) Green signal light changed from +10 to +20 seconds in Rally1 configuration Versione 1.8.3 1) Ranking added with run 0 for Single Starts program 2) New "Playtime" configuration added to Simple Stopwatch program 3) Option of managing two or more races in Parallel Slalom Versione 1.8.4 1) New function "Number of STOPS needed to finish" added to Single Starts program. If active, the finish event also generates a start event for the next run. This function is suited to relays or to track races in which two or more competitors compete at the same time. Versione 1.8.6 1) New protocols for data upload from PC added (see "Protocol Tranmission" manual) 2) Possibility of sending the competition configuration in the "Show Jumping" program (see "Protocol Tranmission" manual): when quitting "race configuration" press ALT + F4 3) New software commands added: "$CLEARLxxx" deletes the start list xxx (0 = all lists), "$CLEARMxxx" deletes the start list for run xxx (0 = all lists) 4) New single MicroTab default displayboard added for Swimming program 5) Choice of penalty addition mode in table C added in Show Jumping program: - "At the end" (the penalty is added at the end) - "Immediately" (the penalty is added immediately but is not taken into account for reaching the time limit) - "Immediat.+TLim" (the penalty is added immediately and is taken into account for reaching the time limit) Version 1.9.3 1) Menu item added to the synchronization menu for uSync connection (only with ports Computer A o Computer B). CORE Version required: 14 or higher 2) "Modem out" added to “Radio” in "Serial ports setup" menu. With this function it is possible to set the encoder with the bib chosen 3) The function "'CONFIG' Keys activity " added in "Hardware setup". If set to "Delete event" and the LCK of CONFIG button is active, all the events are discarded 4) "False start" menu added for managing false starts. 5) Program for managing TimeLink device in PC-ONLINE finished 6) New function "Groups gap" added in Simple stopwatch program. This function is suitable for in-line cycling races for managing time differences of groups at the finish 7) "Cycling" configuration added in Simple stopwatch program with “Groups gap" set at 1 second 8) "RockSpeed wire" and "RockSpeed wireless" configurations added to Parallel Slalom program for managing competitive climbing races with two competitors 9) "Climbing" configuration added in Swimming program for managing competitive climbing races with up to ten competitors 10) "Skating Quad" configuration added in Dual Timer program for skating races with two pairs on the track 11) "Skating Multi lane" configuration added in Dual Timer program for managing races with three persons on the track 12) Management of following displayboards added: uTabPix (Microgate), Gemini (Omega), Ares (Omega) ATTENTION: - When using LinkPod or EncRadio devices with tick serial output or displayboards it is advisable to insert a delay (for LinkPod 120ms, for EncRadio 200ms). This can be set in "Serial configuration" by pressing ALT + F2 or in the displayboard menu - When using Rei2Net make sure that all the stopwatches in the network have the same version number - An error has been detected in the Microsoft HyperTerminal program when a number that starts with 111 is sent. To eliminate this problem, before using Hyperterminal save the configuration, close the program and then reopen Hyperterminal *= Available only in the full version